Husqvarna 20221007 Power Cord 100Ft Triple Breaker Kit 30A 9-20 Hp 240 Volt 3 Phase Grinders Polishers

Husqvarna 20221007 Power Cord 100Ft 3 Breaker 30A 240V 3Phase Grinders Polishers Dust Collectors Shot Blasters L15-30 [20221007]

Click to enlarge

Your Price: $1,177.15
Part Number: 20221007
Quantity:
Estimated shipping cost: $ 115.00

Husqvarna 20221007 Power Cord 100Ft Triple Breaker Kit 30A 9-20 Hp 240 Volt 3 Phase Grinders Polishers Dust Collectors Shot Blasters L15-30

For temporary hook up only.
Hooks to 95% of business in the USA to run your 9-20 Hp 240 volt 3 phase 3 Pole grinders, dust collectors, polishers, shot blasters or pressure washers, and more that use less than a 11KW (11,000 watt motor)

Bundle includes:
Husqvarna 100 ft Wire Cable Stranded Style 8/4 SOOW Power Cord Black Rubber Jacket L15-30 Ends 30 Amp 3 Phase 20221006
with Three 30 amp Breakers starter kit
QB Assembly includes:
(100) 100 feet of 8/4 35 amp wire 84000 / or .2 of a 500 ft roll.
(1) L15-30P 3 Phase Male plug
(1) L15-30R 3 Phase 30 amp female connector.
(1) 205594652 Square D 30 amp 3 Pole Breaker
(1) 300224206 GE 30 amp 3 Pole Breaker
(1) 196375 Siemens 30 amp 3 Pole breaker
Customer self assembly.

Instructions;
Locate the brand of breaker box in the building.
Example if this is a GE branded panel, you will use the GE branded breaker.
If you are connecting to a Square D panel, you will have to use a Square D breaker, etc.
These are the 3 top brands of breakers that are used on the inside of the building or home.
Not all building has 3 phase current but most commercial location will
Turn off 'main' breaker that feeds this sub panel. (usually outside)
Remove the outer cover / door of the breaker sub panel to expose breaker mounting.
Test voltage to sub panel to confirm you have turn off the power.
Note the 8-4 gauge X 100 foot power cord provided in this starter kit is wired with Black, White, Red, and Green internal wires
Strip outer jacket of male side of this 8-4 X 100 ft power cord back at least 2 feet.
The strip each colored jacket from each wire back 5/8 inch.
Install the green wire into the common bar or case ground bar inside the sub panel.
Install the white wire to one of the screw blocks in one side of the 30 amp breaker that matches the brand of breaker box.
Install the black wire into the other screw in the other side of this 30 amp breaker block.
Install the red wire into the other screw in the other side of this 30 amp breaker block.
This is one wire for under each screw in the 30 amp breaker.
Check and see if there are empty spaces in the bottom of the breaker box sub panel to snap in the new breaker.
If not, you will have to lift out one or two of the existing breakers to insert this 30 amp breaker into its position(s.)

Install the L15-30P male plug onto your 9-20 HP 240 volt 3 phase machine (when you open up the male plug you will see a green screw for the ground wire and the 3 gold screws are for the remaining 3 hot wires)
Install the Female L15-30R Round receptacle connector to the 8-4 X 100 foot power cord. White wire to gold screw, black wire to gold screw, red to gold screw, green wire to green screw.

Notes: To lift out a breaker grab the wire side of the breaker and roll the back of the breaker out and towards the center of the panel. To install, the reverse takes place. Nose in the front of the breaker, then push the rear of the breaker down and in to snap into place. Tuck the wires are needed to prevent any shorts.
Install large sign on wall, "Stay Away, Live Panel, Hot Wires, Do not touch, Electrical Shock or Death Can Occur!
There are other breaker brands that are used in the USA, Canada, and Mexico but this is a good starter pack.
Turn main outside breaker back 'ON' that controls sub panel and test voltage to confirm you are not on a 208 volt, or 460 volt panel. Test equipment/machine.
This is for temporary short term use only and should not be used as a permanent installation.
If you question any of these procedures, please consult with a certified electrician in your area.
Please remember the 80/20 electrical rule. If you are going to plug into a 30 amp breaker and draw long term (more than 8 hours) the running device needs to be under 80% of 30 amps = 24 amps max.

If you load the breakers past 30 amps, you could upgrade to 40 amp breakers as needed. This would only happen if the voltage in the building you were servicing was under 240 volts as this would cause the amps to go up.
Test the voltage between the any two of the hot legs on the breaker screws.
If they ready 240 volts, you go to go.

Options

Single phase cord for home use.
L6-30 Extension Power Cord 230 Volt 50 ft 10 gauge 3 wire 10-3 with Husqvarna PG400 PG510 PG530 Grinders 10134753 Blastrac 1-8DEC shot blasters

Consider adding this kit for a wider source of options
The ReverseL6-30R power supply box is for using under 20 amps at 240 Volts single phase commonly for 4 Hp grinders and vacuums.
Husqvarna Blastrac 1-8DPS30 Single Phase L6-30 Basic Power Supply No Generator Required 240 Volt 50 ft 10-3 Blastrac 1-8DEC 20210511

Search Terms:
How to hook a concrete grinder to a circuit panel? How to hook a concrete dust collector to a breaker box?
How to hook a shot blaster to a circuit breaker box panel?
How to hook a 240 volt sander to a breaker box?

Steambrite processes shipments daily by Fedex, UPS, and USPS (for small packages), as well as a using a variety of freight carriers for oversized/palletized shipments. While the Steambrite website DOES reflect what is available for purchase, it does NOT reflect available inventory at our local warehouse (San Antonio, TX). Special order, or custom build items may take up to 30 days to arrive, but orders shipped from within Steambrite's warehouse inventory are generally processed and shipped in 2-5 business days. Equipment small enough to be sent by ground should typically arrive within 3-5 business days after shipment. Oversized shipments could take in excess of 6-8 working days to arrive after shipment, and ground shipping times are not guaranteed.
Husqvarna 20221007 Power Cord 100Ft 3 Breaker 30A 240V 3Phase Grinders Polishers Dust Collectors Shot Blasters L15-30 [20221007]

Click here for our full shipping policy. Specifications are subject to change without notice.
Steam Brite Inc shall have no obligation or liability to buyer whether arising in contract (including warranty) tart (including active, passive or imputed negligence) other otherwise for loss of use, revenue or profit, or any other incidental or consequential damages with respect to any non-conformance or defect in any items provided here under. Display images are for reference only, note that all purchases are fulfilled by the part number ordered. You our customer agrees to indemnify Steam Brite Inc and to hold it harmless from and against any and all claims, cost, liabilities, damages and expenses, including attorney's fees, resulting from personal injury or property damaged caused by the Products.
Warranty Disclaimer: Buyer's sole and exclusive remedy for defects in the products shall be as provided in the manufactures's warranty and any other rights provided by law against the manufacturer. Steam Brite, Inc makes no other than as specified in this agreement. All other warranties, express or implied, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are hereby disclaimed.

This product was added to our store on Wednesday 05 October, 2022.

Product Datasheet

20221007 for only $1,177.15 - Steambrite's price on the Extension Power Cords - 20221007 extractor, Equipmentcarpet cleaning equipment, Equipment flood restoration, Equipment carpet cleaning machine,

Husqvarna 20221007 Power Cord 100Ft Triple Breaker Kit 30A 9-20 Hp 240 Volt 3 Phase Grinders Polishers Dust Collectors Shot Blasters L15-30