Karcher Windsor 8.637-904.0 Puck Step 1 Diamond Resin Honing Disk 5 Inches 8 Pack
Eco Friendly Stone Polishing Pad - Pucks Kit
Available Kit Include: Step 1 - 4 Aggressive Grit, Step 2 - 4 Moderate Grit, Step 3 - 4 Light Grit, Step 4 - 4 Finishing Grit - Step 5 - 1 17" Finishing Touch Polishing Pad 11,000 Grit (total 17 pads)
This part number is for eight disks of Step 1.
Pucks are 5" super thick diamond discs unlike any other diamond discs on the market today. Pads can fully restore marble, travertine, limestone, terrazzo, and other natural stone floors and surfaces with NO chemicals or polishing compounds.
We recommend the Pucks be mounted to our thick Rubber Riser. The riser acts as a cushion to make operation more comfortable and helps the Pucks glide over uneven surfaces. The rubber risers are available in 17" or 20". This riser goes on the bottom of the floor machine.
We recommend a 3-4 Puck configuration with the 17" and a 4-6 Puck configuration if you are using a 20" machine. It really is a matter of preference.
Adjust your downward pressure. Install 3 to 8 pucks. You need 3-4 Pucks evenly spaced on a Velcro drive plate (17")on a floor machine. Why 3-4 or even 5? Some people will prefer to run only 3 to increase the psi on the segments where they contact the floor. Some prefer 4 or 5 or even 5 through 8 pucks for ease of operation and balance.
Floor Machines - 17" (175-350 rpm)
Coverage: 1500-15,000 sq. ft. per set
The Fastest Stone Restoration System on the Planet!!!
Polish like a pro Better than factory finish in less time, every time
Step 1 replaces = 100-200-400 grit to remove deep scratches
Step 2 replaces = 200-400-800 grit to remove mild to moderate scratches and etching
Step 3 replaces = 800-1500-3000 grit
Step 4 replaces = 3000-8000 grit
Steps three and four are to prepare the surface for polishing.
Recommend to have two of the 11,000 grit pads- 1 to be dedicate as a wet polish pad - 1 can dedicate as a dry polishing pad. Some surfaces can get even a little more "pop" by doing additional passes withe dry 11K.
How long will they last? Depending on stone hardness, type of equipment and proper use they’ll last 1500-15,000 sq. ft. per set. That’s a wide range but these factors can dramatically affect lifespan.
The pucks are made from the same material that is used on the larger Cheetah Pads. The Pucks have Velcro on the back and attach to a riser on the bottom of your standard 175-300 rpm floor machine or planetary.
You follow the regular suggested use and instructions for the Cheetah Pads as you would the Pucks. Please remember that having a full set is recommended to be prepared for any situation. You rarely to start with Step 1 on every job unless the damage is severe.
The Stone Craftsman’s Dream Come True
Up to 70% reduction in labor
As much as 75% lower cost
Work well on any floor buffer, orbital or planetary machine
No heavy duty equipment required
Extremely fast cutting
Better than factory finish in less time, every time
No acidic polishing compounds or crystallizer are needed! Only water
COMPLETELY GREEN PROCESS
Diamond Pads That Perform Stone Restoration in Half The Time
Very easy To Use
Work well on any floor buffer, orbital or planetary machine
No acidic components
Extreme concentration of micro abrasives
Works incredibly well on ALL Marbles, Travertine, Limestone, Terrazzo and Polished Concrete
Chemical free Diamond pads are an Eco Friendly way to achieve a dull hone on Travertine, Marble, or Limestone Floors, countertops or walls.
Use on floors walls or countertops with little to no lippage (uneven tiles).
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished.
Safe on all stones and tile, will not damage any stone
Professional strength formula.
Instructions
1. Sweep or vacuum to remove all abrasive soils.
3. Rinse surface thoroughly.
4. Place 3-6 Pucks evenly spaced on a Velcro drive plate on a floor machine. We recommend the Pucks be mounted to our thick Rubber Riser. 17" Floor machines usually use 4 to 8 disk while 20" floor machines usually use 5 to 10 pucks on the disk at a time.
5. 175 rpm machines work best with 30 lb - 40 lbs weight set or drive plate. 300-350 rpm machines do not require extra weight.
6. Apply enough water to 2’ X 5’ area to lightly wet the surface. No need for huge puddles.
7. Move the floor machine in an oval pattern, counter clockwise to keep the water inside the work area.
8. Check surface after 15-30 seconds to see if desired results are achieved.
9. If YES, repeat steps 6-8 on the rest of the room one section at a time.
10. Overlap sections by 4” - 6” to keep an even finish.
11. If NO, repeat steps 7 & 8 until desired result with that grit is achieved (usually 15-45 seconds per 2’ X 5’ area).
12. Rinse whole area between grits.
13. Rinse pad thoroughly after each use and allow drying.
14. Repeat steps 6-10 with grits as you go to higher number until desired finish is achieved.
Optional Rubber disk are available in diameters of 5", 8", 17" and 20" in both a soft 1" thick or hard 1" thick.
If your surface has any lippage use the soft. These disk are made from a closed cell sponge rubber with velcro on one side and velcro hook on the other. Drive with any pad driver.
Buy more, Save more.
Compare to current or past OEM associations:
575812
8.637-904.0
86379040
Options:
| 
English
French
Spanish
German
Italian
Portuguese
