Mytee Etm-lx-plus Escape Post Heat Exchanger Only Titanium Medium Pressure 20220522 Heater Only 425Psi

Mytee ETM-LX-PLUS Escape Post Heat Exchanger Only Titanium Medium Pressure 20220522 Heater Only 425Psi [20220522]

Click to enlarge

Your Price: $2,518.17
Part Number: 20220522
Quantity:
Estimated shipping cost: $ 21.00

Mytee ETM-LX-PLUS Escape Post Heat Exchanger Only Titanium Medium Pressure 20220522 (2 month build time required)

Helps that the heat from the vacuum motors 185 degree exhaust and transfers to the high pressure rinse water after the water pump.
100% more water molecule vibration than standard garden hose water temperature.

Constructed of titanium shell and titanium coil
Rolled formed to shape and then precision weld
Specialty designed built in flow restrictor to assure maximum heat exchange
Designed to minimize pressure loss in the heating system
Leak tested to assure that they are totally functionable
Compact in size and require minimum installation space
Significant energy savings
Equipped with stainless steel holding brackets

Max BTU Output:	135,000
Max Hot Water Flow:	11 GPM
Max Air Flow:	225 CFM
Heat Transfer Area:	2.5 Sq. Ft
Empty Weight (lbs):	4 lbs
Water Connection:	1"
Air Connection:	1-1/2"
Height (Inches):	20"
Width:	5-1/8"
Max. Working Pressure:	425 psi
Max. Working Temp (F):	230°F

.
Notes: This is not everything you need to heat the water for a the Mytee Escape truckmount.
Water and air flow should be in apposing directions for best results.
Do not allow to freeze.
Heat exchanger will not work until the wand is on the floor. I takes 5 minutes for the vacuum motors air exhaust to heat up after the wand removes over 50% of the air flow from the partial occlusion.
Heat exchanger is stored on the side of the truckmount so the hot air can blow out the door of the van or trailer. Water flow is the opposite of air flow direction. The high pressure water comes in the front and the hot water comes out the rear while the hot air comes in the rear and leaves the front. You will have to have a jumper hose from the high pressure out off the face of the machine to the heater intake.
The max recommended temperature for the 2" ID vacuum hose is 140 degrees F. The air coming out of the back of the Escape Plus is over 185 degrees F once the one is on the floor and they have been running for 5 minutes. This means it is possible to melt the vacuum hose. We do sell 450 degree rated silicone hose below. You can also stack the medium pressure heater with the low pressure heater below. The medium pressure heater must be installed closest to the hot air and the low pressure mounted secondary. In other words, use the air that leaves the medium pressure heater to feed the low pressure heater with a 1.5" nylon pipe nipple.

Options below:

Mytee ETM-LX-PLUS Escape Pre Heat Exchanger Stainless Steel Low Pressure Starter Kit 20220521

Upgrade hot air transfer hose from plastic to silicone rated for 450 degree F.
SteamBrite 20220520 Truckmount Through the Floor Exhaust Hose 2in ID X 6 ft Long Silicone

Connects to male nipple on heat exchanger to convert the 1 Male pipe to 1" female pipe connection
2 units needed
Brass Coupler 1 Inch Fip X 1 Inch Fip Brass Coupling 28063 103AH-F

Two units needed
1in Mip X 1/4in Fip Brass Bushing Adapter 28112

Two units needed
1/4in Mip X 1/4in Mip Brass Hex Nipple Pipe Thread BR072 P/N-3325-4 - 8.706-780.0 28212L

Screws onto the 2" ID vacuum hose on one side and slips over the AH69 fitting
Clean Storm AH44 Vacuum hose Cuff 2in Thread X 2.0in Slip - 2in Standard 8.708-904.0 B016 J11630 530009

Goes between H136V and AH69
Hose Vacuum Hose 2.0in ID Double Lined By The Per Foot 20140808 (NO Hose Cuffs)
Order about 6 - 10 feet depending on heat exchanger placement.

To assist with connecting 2" ID vacuum hose to the back wall air exhaust of the Escape
Mytee H136V Male Vinyl Hose Cuff EACH

Installed on inbound side of heater to assist in connection of 2" ID vacuum hose
If you are going to use the optional silicone hose, you will have to file or grind off a little plastic as the barbs are just over 2" wide.
2in Barbed X 1-1/2in Mip Plastic Connector Vacuum Port 20130429 Insert Fitting AH69

Join multiple heaters in series for even more heat.
Plastic White Nylon High Temperature Hex Pipe Nipple 1-1/2 Inch Mpt 28618W

Question: Can this be used on the ETM-LX-115?
Answer: You can but since this other model only has 2 vacuum motors in it, it will not get near as hot.

Question: What is the side bleeder port connection size?
Answer: This is a dry well that does not need to be capped off. It is for 3rd party sensor to monitor the air temperature of the heat exchanger.

Question: Does the heat exchange reduce the air flow to the wand?
Answer: No it does not as once the wand is on the carpet the air flow through the truckmount is less than 50% of what it is open flow. The heat exchange can handle 225 cfm and so the truckmount open flow rating would have to be over 450 cfm before it was restricting the dry times. We tested the Escape plus to have 242 cfm open flow and 121 with the wand on the carpet. (sorry 350+ cfm from Mytee is a misprint) Read more HERE.

Question: What is the maximum water temperature I can achieve with this heater?
Answer: About 185 degrees F max. Example like in upholstery cleaning. Depending on your flow rate for carpet cleaning will be less. You can stack the low pressure heater with the medium pressure heater for improved results and also feed system with building supplied how water with the hose reel below.

Question: Can you make this to handle higher pressures for tile cleaning?
Answer: So far no. The thicker walled metal makes it cost too much as well as then does not transfer the heat as well. Currently you have to disconnect the heater water pressure when cleaning tile.

Optional

Transfer the building supplied hot water out to the Escape Heater to further increase the heat.
Clean Storm Live Reel with 100 ft Hot Water Transfer Garden Hose 3/8in ID Hose included SBM100GL 20220406

Steambrite processes shipments daily by Fedex, UPS, and USPS (for small packages), as well as a using a variety of freight carriers for oversized/palletized shipments. While the Steambrite website DOES reflect what is available for purchase, it does NOT reflect available inventory at our local warehouse (San Antonio, TX). Special order, or custom build items may take up to 30 days to arrive, but orders shipped from within Steambrite's warehouse inventory are generally processed and shipped in 2-5 business days. Equipment small enough to be sent by ground should typically arrive within 3-5 business days after shipment. Oversized shipments could take in excess of 6-8 working days to arrive after shipment, and ground shipping times are not guaranteed.
Mytee ETM-LX-PLUS Escape Post Heat Exchanger Only Titanium Medium Pressure 20220522 Heater Only 425Psi [20220522]

Click here for our full shipping policy. Specifications are subject to change without notice.
Steam Brite Inc shall have no obligation or liability to buyer whether arising in contract (including warranty) tart (including active, passive or imputed negligence) other otherwise for loss of use, revenue or profit, or any other incidental or consequential damages with respect to any non-conformance or defect in any items provided here under. Display images are for reference only, note that all purchases are fulfilled by the part number ordered. You our customer agrees to indemnify Steam Brite Inc and to hold it harmless from and against any and all claims, cost, liabilities, damages and expenses, including attorney's fees, resulting from personal injury or property damaged caused by the Products.
Warranty Disclaimer: Buyer's sole and exclusive remedy for defects in the products shall be as provided in the manufactures's warranty and any other rights provided by law against the manufacturer. Steam Brite, Inc makes no other than as specified in this agreement. All other warranties, express or implied, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are hereby disclaimed.

This product was added to our store on Friday 20 May, 2022.

Product Datasheet

20220522 for only $2,518.17 - Steambrite's price on the Heater Repair Parts - 20220522 extractor, Equipmentcarpet cleaning equipment, Equipment flood restoration, Equipment carpet cleaning machine,

Mytee ETM-LX-PLUS Escape Post Heat Exchanger Only Titanium Medium Pressure 20220522 (2 month build time required)